Technical Spesifications: |
|
Appearance: |
Gray fine powder |
Powder Density: |
~ 1,40 kg/lt |
Water Mixture Ratio: |
6 lt water / 25 kg |
Pot Life : |
20 - 30 minutes |
Walking Time : |
~ 24 hours |
Abrasion Resistance Against Rotating Wheel: |
≤ 1 cm3 28 day (EN 13892-5) |
Pressure Resistance : |
≥ 25 N/mm2 28 day (EN 13892-2) |
Flexural Strength : |
≥ 7 N/mm2 28 day (EN 13892-2) |
Application Temperature: |
+5°C ile +35°C between |
Cement based , eliminates surface defects and unwanted roughness , self - leveling and can be applied up to 10 mm thickness . It is a C25 class floor leveling system .
Usage areas :
• In indoor and dry environments, • In residences ,
• In hospitals,
• In educational buildings ,
• In shopping centers , stores and markets, • Ceramics, granite, marble, wood , parquet , laminate,
It is used to level the surface with a thickness of 2 - 10 mm before laying carpet , linoleum and PVC coatings .
Advantages :
• It is applied in 2- 10 mm thickness .
• It is applied quickly and easily .
• It spreads on its own and reaches the level , eliminating the roughness of the subfloor .
• The final finish surface provides a homogeneous appearance .
• It has high adherence to the ground .
• Suitable for underfloor heated floors .
• Can be applied on old concrete floors .
Preparation of the surface :
• The concrete subsurface must have sufficient compressive strength ( Minimum 25 N
/ mm 2 ) . • Care should
be taken to ensure that the application surface is cured . • Weak concrete on the surface should be removed and the gaps should be filled with appropriate repair mortars . • The application surface must be cleaned of substances that prevent adhesion such as dust , oil , tar , pitch, paint, silicone , curing material , detergent and mold oils .
• On heavily worn concrete surfaces , primer application should be started after increasing the adherence with cement mortar containing DEMATHERM LATEX .
• The surface must be primed with DEMAFİX Floor Primer to prevent absorbency and increase adherence .
• The level difference on the ground to be applied should be determined using tools such as hose scales and levels.
Preparation of the mortar :
• DEMAPHIC is done .
• The prepared mortar is left to mature for 2 - 3 minutes and is used by mixing again for 1 - 2 minutes .
• The mixture in the container should be consumed within approximately 30 - 35 minutes .
Application Information:
• Following priming of the surface, DEMAFIX SELF - LEVELING SCREED THICK , - C25 application should be started after at least 30 minutes , depending on weather conditions .
• The prepared mortar in a fluid consistency should be poured onto the surface . In order to facilitate the spreading process , its thickness should be adjusted by making corrections in places with a notched trowel . During application , a hedgehog roller and spiked shoes should be used to avoid air bubbles remaining inside the product .
• In applications in large areas , uninterrupted application is required to prevent the formation of cold joints . For this reason, to ensure the continuity of the pouring process , the material should be prepared in more than one bucket and the application should be completed by pouring it on the ground one after the other .
Consumption :
1.6 - 1.8 kg/ m2 ( for 1 mm thick person )
Attention:
• Avoid application at temperatures below +5 ° C and
above +35 ° C. • Avoid application in areas that are frozen , at risk of freezing within 24 hours , or exposed to direct sun and wind .
• Never add water or
powder to expired mortar . • Avoid rapid drying of the material .
• You should wait at least 3 days for it to be coated . • It is not applied in outdoor and industrial areas .
• It is not applied on wet surfaces exposed to moisture .
• Apply on old concrete surfaces , with surface repairs and a primer layer .
• In systems with underfloor heating , the heating system should be turned off 24 hours before the application and turned on 72 hours after the application .
PACKAGING:
In 25 kg craft bags
Shelf Life :
in moisture-free environments and in its unopened packaging on
a pallet with a 10-layer stack for 12 months.
Health and Safety :
As with all chemical products, contact with food products , skin , eyes and mouth should not be avoided during use and storage . During the application , work clothes , protective gloves , glasses and masks that comply with work and worker health rules should be used . If swallowed by accident, seek medical advice . In case of contact with skin, wash with plenty of water . It should be stored in places where children cannot reach it .