It is abrasion - resistant , consisting of a mixture of special type cement , basalt aggregate and performance - enhancing chemical additives , applied monolithically to fresh concrete surfaces .​​ It is a powder surface hardener . It provides wear, impact, dust and abrasion resistance against light and medium loads on concrete surfaces .

Usage areas :​​

• Indoors and outdoors , •
In factories , business centers , •
In garages , car parks and basement floors,
• In loading and unloading areas , •
In metro stations and underground passages ,
• It is used in parks and gardens , pedestrian paths and sidewalks .

Advantages :​

• It is applied monolithically to fresh concrete .
• When DEMAFI XY SURFACE HARDENER is applied , the abrasion resistance of the concrete surface increases 2 - 3 times compared to normal concrete .
​​ • It is a part of the surface on which it is applied , and does not wear out or flake off .
• It is economical and long - lasting .
​ • It is ready for use .​ It saves significant time with its fast and easy application feature .​ • Provides resistance to wear and impact on concrete surfaces and joint edges .
• It creates a surface that is resistant to weather conditions and freezing and thawing .
​​​​• The surface is easier to clean and its resistance to oils is higher than normal concrete .​​​​• Does not oxidize.
• Provides higher impermeability compared to concrete .​​ • Offers different color options .

Preparation of the surface :​​

• If DEMAFİ​​​​​​​​​​​​​​​​​​​​​​​​​
• The fresh concrete to be applied must be wet enough for the DEMAFI XY SURFACE HARDENER to absorb the moisture it needs .​​ The wetness level of the surface is extremely important . If the surface is too wet , the DEMAFİ XY SURFACE HARDENER will disappear within the thickness of the concrete itself and lose its effectiveness .​​​​​ If the surface is too dry, the product will not bond to the surface and the result will be negative .

Application Information:

• Depending on the dimensions of the ground , the anos are placed one full and one empty in a 4 - 5 m wide area . Where
necessary , mesh steel is placed inside the tiles and the leveling process is completed and concrete is poured . • The concrete is leveled after it is poured , and its placement is ensured by the application of a vibrating float . • When the concrete has hardened to the point that a footprint of at most 2 - 3 mm depth will remain when you step on it , the DEMAFI XY SURFACE HARDENER will be removed . 1/2 of it is spread evenly on the ground , manually or with a mechanical spreader .
• In order for the DEMAFİ​​​​​​​​​​​​​​​​​​​​​​​​​​​​

• The material is expected to absorb the water of the concrete, become moist and acquire a dark color . Care is taken to ensure that the color is equal on all sides of the floor . The material is thoroughly fed into the ground with a trowel
to ensure integration .
• Some material is spread in an 8 cm strip on the edges of the ano and dilatation joints that are under the highest load and applied with a trowel.
• The remaining 1/2 of the material is spread by sprinkling on the ground , it is waited for it to get moist and a dark color , and it is fed into the ground with a trowel.
• When the surface is hard enough to walk on , it should be polished with a steel trowel ( helicopter ) .​

Curing :​

order to prevent premature drying and cracking , DEMAFİX CONCRETE CURING materials should be used on the surface after the final finishing process .

Consumption :​

For light and medium loads : 4 - 5 kg/ m2

Attention:

• Avoid application at temperatures below +5 ° C and above +35 ° C.​​​​​​​​​​

• Avoid application in areas that are frozen , at risk of freezing within 24 hours , or exposed to direct sun and wind .

• Excessive polishing should not be done , and the product should not be thrown away during application to prevent the aggregate from separating from the cement .​​​​​​​​​​ i r.

• The surface should not be polished with a steel trowel or tray before the application of DEMAFIXY SURFACE HARDENER .​​​​​​​

• In correct applications , ambient humidity is between 40 - 80%
relative humidity . At low relative humidity , efflorescence may occur on the surface , at high relative humidity , sweating on the surface , slower curing and hardening may occur , and the application may take longer . It may be necessary.

PACKAGING:

In 25 kg craft bags

Shelf Life :​​

in moisture-free environments and in its unopened packaging on a pallet with a 10-layer stack for 12 months.

Health and Safety :​

As with all chemical products, contact with food products , skin , eyes and mouth should not be avoided during use and storage . During the application , work clothes , protective gloves , glasses and masks that comply with work and worker health rules should be used .​​ If swallowed by accident, seek medical advice . In case of contact with skin, wash with plenty of water . It should be stored in places where children cannot reach it .